Choosing a Grout Color

Dear Rob:

My wife and recently ordered some tile to use when we remodel our bathroom, but we can’t seem to agree on what color grout to use. We are concerned about the grout getting dirty, but we’d also like to choose something that will look nice with our tile. Do you have any pointers for choosing grout color?

Tim from Texas

Dear Tim:

Choosing a grout color can be tough, because you have so many choices these days. To keep it basic though, you can either choose a color that is the same as the tile, one that contrasts with the tile, or you can choose a neutral color.

• Matching – By matching your grout color as closely as possible to your tile color, you make the grout lines less obvious. This accentuates the tiles them selves, and not the pattern of the layout. This choice is generally best when you choose a beautiful tile in a simple layout.
• Contrasting – Choosing a contrasting grout color draws attention to the layout of the tile. This is often desirable if you choose a mosaic tile in an interesting geometric design or if you use a more complicated or decorative tile layout.
• Neutral – When all else fails a neutral color like tan, beige or light gray can work in most applications. Keep in mind the white grout often yellows over time, so it probably won’t be a low maintenance choice.

Darker grouts are less apt to stain, so if you are tiling a counter top or a high traffic floor, keep that in mind. On the other hand, lighter grouts are less likely to fade with sunlight or strong cleaners. You can always re-stain your grout if it becomes faded or discolored, or if you are just ready for a change.

Hope this helps you make your decision.

-Rob

Scratched Hardwood Repair Looks Dull

Dear Rob:

I touched up a scratch on my red oak hardwood floor using the same finish that the floor contractor used and it looks duller then the rest…… it was a oil based finish called Fabulon.

-Kim From Alabama

Dear Kim:

I am sorry to hear about your scratched hardwood floor problem. Dull finish or mismatched finish is very common when blending scratch repairs on hardwood floors, and there could be several reasons for this:

1. You may not have stirred the polyurethane well enough before applying it.  If you only dipped your brush into the top of the finish, without stirring well, that may have led to your finish not being shiny.
2. You may have used the right material, but the wrong sheen.  If you didn’t use a can of polyurethane that was left over from your project, call whoever applied the finish to double check what sheen they used.
3. If you sanded the area around the scratch, you may not have applied enough polyurethane in the sanded area, resulting in a dull area because the finish is thinner in that area.

It’s tough to know for sure which of these possibilities applies to your situation, but hopefully they will get you started with solving your problem.

I recommend that you carefully outline with tape the adjacent boards along their edges and then gently scrape the area that you originally touched up with a hand held floor scraper that you can get from any big box home retailer.  That will take the finish back down to nearly bare wood, but do not go all they way down.

I would properly stir, not shake, the polyurethane.  Then carefully apply a thin coat of finish.  Let that coat dry and repeat. If all went well, your floor should be as good as new.

-Rob

Fixing Dull and Shiny Spots in Hardwood Floor Finish

Dear Rob:

I recently had my floors refinished and the poly came out very uneven. Some places it’s really shiny and others, its very dull. Any ideas on a quick fix to even it out? I have to move furniture into these rooms this weekend.

-Lacey G. from Merrimack, New Hampshire.

Dear Lacey:

I assume that you have a polyurethane floor, so I will base my answer on that. The dull and shiny spots in your hardwood floor indicate that your installers did not apply the finish correctly.

Dull spots in polyurethane floors usually indicate that the finish was not applied carefully, the applicator had a dry spot on it, or the finish was thinned out with a solvent such as mineral spirits. The latter is a big mistake, but a common shortcut in the industry among people trying to save money on materials.

Shiny spots in polyurethane floors can be caused by the finish not flowing out properly and pooling in areas, or inconsistent screening between coats of finish.

There is no quick fix for this, what I recommend is that you have the refinishers come back and screen and coat the floor. A screen and coat is a procedure where the floor is lightly sanded (or screened) with a floor maintainer or buffer, instead of a floor sander. This light sanding evens out the finished, cleans away debris, and roughens the surface, so another coat of finish will be able to properly adhere to the existing finish.

There is no other way to even out the finish.

-Rob